This post was originally written for Eric’s blog. Check the original post and his other blog posts here.
Every day of my Carleton job has been a new adventure. I get opportunities to work on creative, innovative projects that I get to run fairly autonomously. In this post, I’ll be talking about the Lightboard.
The Lightboard was one of the first projects I was assigned to during my starting week at Carleton. I was given the following problem: research other Lightboards around the country, and try to figure out how to make ours work well. Before we delve into solving the problem, I should probably answer the most obvious question: what is a Lightboard?
A lightboard is, in essence, a clear whiteboard. The instructor stands on one side of it and writes on it with a fluorescent marker. A camera is on the other side that captures the writing that glows on the screen. The footage is then flipped, cropped, and edited for color and lighting. We end up with footage that captures not only what the instructors are writing, but also their full expressions and face, rather than their back or hands.
The original Lightboard was developed at Northwestern by Michael Peshkin, a professor of Physics. His site not only shows his (very sophisticated) Lightboard build, but collects build instructions and documentation from Lightboards at schools around the world. This was extremely helpful in figuring out how to solve our own issues with the Lightboard.
With that brief introduction, back to the problem at hand. We already had a frame with plexiglass installed, but it was nearly impossible to capture what was being written on the board, and the audio was also muffled. The audio problem was relatively easy to solve; we simply attach a wireless lavolier microphone to the presenter, and the audio streams directly to the camera, instead of having to go through the plexiglass. Solving the visual issues was a bit more of a process. First of all, the plexiglass was extremely reflective, and our first attempts often captured more of the camera than the presenter. Second, if the presenter was well-lit enough to see, it meant that any writing was impossible to see. This was what an early test looked like.
Idea 1: Adding lights to the board surface.
First, I attempted to add better lighting to the outside of board. This was simple enough. I had bought some simple IKEA lights [link] to install in my apartment bookshelves, and figured they might help light the surface of the board, as they were relatively flat and easy to place where I wanted. I stuck them on the front of the plexiglass and angled them down, hoping that it would help make both the markers and the presenter more visible. It did help, but not in the right way. Even with fluorescent markers, the writing was barely distinguishable.
Next, I tried adding blacklights to the board. My reasoning was that backlights help things glow, and that it would really boost the intensity of the fluorescent markers. Spoiler alert: It didn’t work. Even with the blacklight, the markers barely glowed. At this point, it became pretty clear that attaching any manner of lights to the surface of the board was not going to work.
Idea 2: Installing lights directly to the side of the plexiglass.
After studying the documentation and other builds more closely, I decided to test what happened when I added lights directly on the edge of plexiglass. I borrowed a spare piece of plexiglass and attached the lights on the edge facing inward. The entire piece glowed as the plexiglass conducted the light from edge to edge. I mounted that piece onto our existing board and did a side by side comparison. The difference, as you can see in the videos below, is very apparent.
With the difference made clear, I got permission from Ben at St. Olaf to physically modify the board so I could install the lighting properly on the top edge of the unit. I removed the top piece and a few support pieces and began to get to work. I lucked out and found that this board had a grove that would perfectly fit the IKEA lights. I installed the lights, remounted the top piece, and added a power strip to the board’s base. The change in quality was fantastic.
Better lighting and editing
With the board now effectively lit, I got to focus on lighting and editing the footage. With lighting, I’ve found that placing a light on both sides of the board to gently light the presenter works quite well. It can’t be too focused, or it creates jarring dramatic shadows. It also can’t be too diffuse, or the board begins to have reflection issues. We also shoot in an otherwise dark studio, with a black background behind the presenter. We use a polarizing filter on our tripod-mounted camera to further reduce reflections, and also cover the red “recording” light with painters tape to ensure it does not reflect on the board.
After we’ve shot the footage, it goes through a brief editing process. I use Adobe Premiere to edit, but the necessary changes would likely be possible on less expensive or free software. I start by color correcting the video, then super-saturating the specific blue of the marker we use to make it extra-visible on the final product. I then apply mirror image filter (called horizontal flip in Premiere) so the writing is facing the proper way, and crop and scale the video so that we only see the board, and not any of the lights or frame. The video is then exported and sent to the presenter for their class or presentations.
We’ve had some really interesting uses so far, even in this initial experimental stage. One of my favorites has been Japanese symbol lessons developed by visiting Professor Miaki Habuka. She has her TA go over the symbols that students in her Intermediate Japanese class need to learn. By using the Lightboard, her students are able to see each stroke of the symbols as they are written, which is an important component in understanding how to properly write in Japanese. Check out the video below to see an example of one of the language lessons. This is just one of the many uses for the Lightboard, and we’re looking forward to many more amazing projects to come.
This is just the beginning of the Lightboard. In later posts, I’m planning to write a more in-depth guide to our specific build with pricing, instructions, and advice. I’ll also continue to show more examples of finished videos and additional modifications or builds.
The following two tabs change content below.
Latest posts by admin (see all)
- Wading into UX - April 21, 2019
- 2019 LACOL Language Instruction Jam - March 25, 2019
- New article published by Janet Russell and Melissa Eblen-Zayas on CUBE - March 22, 2019